DFM & Design Tips

Both Clevis Holes Pass Inspection. Why Will the Pin Not Go Through?

Diagnose a clevis pin that passes each ear separately but not the pair. Separate bore size, axis alignment, edge defects and mounted distortion.

DRAmetal Engineering Team November 3, 2026 6 min read
Both Clevis Holes Pass Inspection. Why Will the Pin Not Go Through?

The pin enters the first ear without resistance, crosses the gap and stops at the second. Both holes were checked with a gauge before the bracket reached assembly. From the side, they even appear to line up. Reaching for a larger drill is tempting, but it answers only one of several questions hidden in that failed insertion.

A pair of clevis holes has to provide a usable passage for a particular pin through a particular assembled configuration. Two acceptable diameters do not automatically produce that passage. The investigation needs to distinguish size, location, orientation, surface condition and the way the bracket is supported during the check.

First establish what actually stops the pin

Use the approved assembly condition and isolate the mechanism before working around it. A diagnostic check should not be performed on a loaded linkage or used as a reason to force a pin into operating equipment. Remove loose contamination and inspect the accessible edges without altering the part.

Note whether the pin stops at the first entrance, the far edge of the first ear or the second ear. Check whether the same obstruction occurs when approaching from the other permitted direction. A burr at an exit edge, a coating ridge and a displaced second bore can feel similar at the assembly bench, yet they require different corrective actions.

Confirm the pin as well. Its diameter, straightness, surface damage and any head or retaining feature belong to the interface. A chamfer can help start insertion but cannot compensate for an incorrectly located bore through the rest of the pin’s travel.

Diameter is only the size of each local opening

A short plug can enter each ear separately while the two openings occupy different positions. Their axes may be offset, tilted relative to one another or displaced relative to the base. A gauge that engages only a small portion of a thin ear does not reproduce the full path of a long pin spanning both supports.

KEYENCE’s location-tolerance explanation distinguishes a feature’s location relative to a datum from the relationship between cylindrical axes. The practical point is not to add every available tolerance symbol. It is to specify the functional relationship that the pin assembly actually needs, using the drawing convention selected for the project.

Likewise, separate coordinate readings can be misleading if each ear was measured from a different local reference. The numbers may each look close to nominal while describing incompatible frames of reference. Use a common, meaningful datum system for the paired features and their attachment to the equipment.

A small tilt matters across the space between the ears

Looking straight at the near hole hides part of the geometry. The pin must also align with the far bore, and it has little freedom to change direction after engaging a close-fitting near bore. The clearance available at the second ear must accommodate the combined geometry, not simply the diameter variation of that second hole.

Ear thickness influences this behavior too. A thicker ear provides a longer bore surface that can guide the pin more strongly. Thin sheet may instead reveal a local edge or oval opening. Neither thickness makes axis control unnecessary; it changes which features dominate the insertion behavior.

For this reason, opening both diameters without review is not a neutral repair. It can increase play, change bearing contact or leave the intended axis in the wrong position. The designer must approve any change to the interface, including a proposed alternative pin.

A sheet metal clevis with two ear bores and a separate smooth pin on the workbench
A full pin path checks the relationship between the ears, not only two separate hole diameters.

Compare the free bracket with the mounted bracket

A bracket may accept its pin on the bench but bind after its base is bolted down. An uneven mounting surface, debris beneath the base or a mounting-hole conflict can change the ear relationship during tightening. The converse is possible too: clamping a distorted bracket into a fixture can temporarily make the pin fit.

Record the inspection condition before comparing results. If the drawing requires a free-state check, forcing the base against a fixture is not equivalent. If the function depends on a specified mounted condition, the fixture must represent that interface and its agreed restraint. Repeat the comparison with the same reference points so movement is visible rather than averaged away.

The related guide to ears bending during bolt tightening addresses distortion introduced across the pivot itself. That is a different load path from the bolts attaching the base, but both can produce a pin-fit complaint.

Trace the first operation that changed the relationship

Review the sequence from flat component to finished bracket. If the preformed holes were acceptable but the formed pair is not, investigate the bend locations, angles and hole proximity to the bend region. If a welded pair changed after fixture release, compare fit-up, welding sequence and the finishing datum.

Coating adds another checkpoint. A masked bore, a coated bore and a bore finished after coating are not interchangeable acceptance conditions. Compare the drawing with the delivered condition before assuming that the fabricator used the wrong cutting diameter. Hole-making sequence should be resolved together with the finishing plan.

Close the issue with a reproducible functional check

For custom sheet metal clevis brackets, agree how bore measurements and an assembly check complement each other. A controlled pin or functional gauge can expose a blocked path, while dimensional inspection explains the source of the problem. Specify the gauge identity, insertion direction, support condition and permitted force rather than accepting “fits with adjustment.”

The first-article pin and gauge guide develops that acceptance method. Successful insertion verifies only the defined fit condition. It does not establish load capacity, fatigue life or operating suitability. Keeping those decisions separate makes the investigation more precise: repair the geometry that failed, confirm the approved interface and avoid turning one successful assembly into a claim that was never tested.

Need a Custom Sheet Metal Quote?

Send us your CAD drawings — DRAmetal's initial response target is within 24 working hours. Quotation, DFM and lead-time timing depend on file completeness and engineering scope.

GET A FREE QUOTE →
DRAmetal Engineering Team

Team-authored manufacturing guidance. Scope, sources, corrections, and project-status labels follow our engineering content policy.