DFM & Design Tips

Partition and Insulator Interfaces in OEM PSU Metalwork

Translate approved PSU insulation and partition requirements into fabrication drawings, with controlled supports, edges, fasteners and assembly checks.

DRAmetal Engineering Team October 15, 2026 5 min read
Partition and Insulator Interfaces in OEM PSU Metalwork

An internal partition can separate mechanical spaces, support an insulating piece or control access within a power-supply assembly. Its purpose must be defined before it is added to a sheet-metal drawing. A metal divider does not, by itself, establish an electrical insulation system.

For an OEM enclosure, the responsible electrical designer supplies the required protected zones and insulating components. The fabrication task is to locate and manufacture the metal interfaces accurately, with finished edges and hardware that match those released requirements.

Collect the design authority’s inputs

Obtain the approved assembly view identifying the partition’s function, material, position and boundaries. Request the selected insulating parts and their attachment details. If electrical spacing or bonding is relevant, the design authority should provide the applicable requirements and acceptance reference.

Do not choose a separation distance from a generic enclosure example. The required values can depend on the complete system and its assessment. When an input is missing, identify it in the interface review instead of allowing the fabricator to infer a safety-critical value from an available gap.

Treat insulator seats as controlled interfaces.
Treat insulator seats as controlled interfaces.

Define supports and datums together

Locate the partition and insulator seats from a reference that remains meaningful after forming. Show their relationship to the board, inlet and module supports. Independent dimensions from unrelated sheet edges can leave the assembled partition correctly sized but incorrectly positioned.

Identify whether the insulating component is supplied by the fabricator or installed by the customer. Include its shape, permitted bearing areas and fixing arrangement. If it can shift during assembly, the design needs an approved locating feature rather than relying on the cover to push it into place.

Design inputFabrication translationRelease check
Partition purposeMaterial and controlled positionMatches approved assembly
Protected zoneNo-intrusion envelopeFinished metal and hardware clear
InsulatorSelected part and locating seatsSupported without unintended contact
EdgesTreatment and affected locationsNo specified edge defects
FastenersComplete approved stackPermitted reach and assembly access

Control edges and fastener intrusion

Mark the edges that contact or approach insulating parts, cables or boards. Specify the required edge treatment and inspection method. A burr or sharp folded corner can change the intended interface even when the partition’s overall dimensions pass.

Show the complete fastener stack, including washers, inserted hardware and the part on the other side. Verify the permitted projection into protected zones using the released hardware selection. Do not treat screw length as an interchangeable purchasing detail once the assembly envelope has been approved.

Finished partition edges need explicit acceptance.
Finished partition edges need explicit acceptance.

Review the finishing and assembly sequence

A coating or post-treatment can alter a contact area or obscure an edge defect. Identify which dimensions and surfaces are accepted in the finished state. Where a particular contact must remain in a specified condition, show its boundary rather than relying on a verbal instruction to the finisher.

Check the assembly sequence with the actual partition, supports and insulating pieces. Confirm that the required parts remain located when the enclosure is closed and reopened. A successful dry fit demonstrates mechanical compatibility only; the equipment’s electrical tests remain a separate release activity.

Keep changes linked to the complete interface

Changing the partition thickness, fastener type or insulating component can affect more than the local part. Review the board envelope, cover fit and intended service movement whenever one of those inputs changes. Do not reuse an earlier mechanical acceptance without assessing the changed relationships.

The linked PSU enclosure project reports board-support and assembly observations, not a partition safety certification. For a new RFQ, send the approved protected-zone model and insulation interfaces along with the enclosure drawing. This lets the metalwork scope be priced and inspected without taking over an unresolved electrical design decision.

Check the released protected envelope with the assembled metalwork.
Check the released protected envelope with the assembled metalwork.

DRAmetal supplies custom power-supply enclosure metalwork to released OEM requirements. Read the mechanical-fit customer project for its specific inspection scopes, then provide your own drawings, mating components and batch plan for quotation.

Need a Custom Sheet Metal Quote?

Send us your CAD drawings — DRAmetal's initial response target is within 24 working hours. Quotation, DFM and lead-time timing depend on file completeness and engineering scope.

GET A FREE QUOTE →
DRAmetal Engineering Team

Team-authored manufacturing guidance. Scope, sources, corrections, and project-status labels follow our engineering content policy.