DFM & Design Tips

The Shim Thicknesses Add Up. Why Is the Assembly Height Still Wrong?

Understand why adding shim thicknesses does not predict every assembled gap. Review tolerance accumulation, interface seating and stack checks.

DRAmetal Engineering Team November 2, 2026 5 min read
The Shim Thicknesses Add Up. Why Is the Assembly Height Still Wrong?

Two thin shims and one thicker shim should provide the required adjustment. The numbers on their packets add up, and each part looks undamaged. After the fasteners are tightened, however, the measured position is different from the expected position. Before blaming the alignment calculation, distinguish the metal thickness in the stack from the behavior of the interfaces around it.

Stacking is useful because it provides adjustment without making a separate part for every possible gap. The trade-off is that every added layer introduces another pair of surfaces to manage. More combinations do not automatically produce more accurate or more stable adjustment.

Three nominal values are not three measured values

Consider an illustrative stack of 0.50 mm, 0.20 mm and 0.10 mm shims. Its nominal total is 0.80 mm. If the permitted thickness deviations were ±0.01 mm on each piece, a simple worst-case sum would allow 0.77–0.83 mm before considering any other assembly effect. These figures demonstrate the arithmetic; they are not a DRAmetal tolerance specification.

That calculation is different from adding actual measurements from the selected pieces. It is also different from measuring the complete stack. The first predicts a range from specified limits, the second describes local readings on individual parts, and the third includes how those selected parts contact under the measurement conditions.

Do not assume positive and negative deviations will cancel. A batch cut from one region of stock can contain several pieces whose thickness deviations have the same direction. Statistical combination requires a justified model of the variation; it should not be used casually to replace a required worst-case clearance check.

Each layer adds another opportunity for imperfect contact

A three-piece stack contains two internal interfaces, plus its interfaces with the lower support and the upper component. A particle, raised edge or local bow at any one of those locations can keep the intended faces apart. Their effect is not necessarily represented by a thickness measurement made at one accessible point.

SKF’s bearing maintenance handbook recommends minimizing the number of machinery shims and limits stacking in its guidance. That is a practical machinery-alignment recommendation, not a universal specification for every engineered shim assembly. Follow the equipment’s approved requirements and investigate why a large number of layers is needed.

The useful principle is to avoid unnecessary interfaces. Where the adjustment is known, an approved thicker spacer combined with a small number of fine adjustment layers may be preferable to a tall pack of thin leaves. The replacement still needs the correct material, footprint and inspection condition; consolidating the count alone does not qualify it.

Equal outside dimensions do not ensure equal support

A stack can look tidy from the side while containing mismatched slots, internal openings or short layers. If the contact footprint changes through the stack, load may pass through a smaller region than expected. Thin layers can bridge local gaps or bend near an unsupported opening.

Use profiles intended to work together. Align them in the specified orientation, with their full working regions seated. A part that stops against a fastener before reaching its intended position should not be treated as an acceptable layer simply because it remains hidden under the component.

This is especially important when replacing a closed-hole spacer with an open-slot shim during maintenance. The slot-versus-hole comparison covers the insertion advantages, but a convenient installation route does not by itself establish an equivalent bearing footprint.

A stack of individual metal shim layers beside a single thicker spacer plate
Individual thickness, complete-stack contact and final joint position are separate checks.

A stack measurement needs a defined condition

Holding a loose stack between fingertips is not the same as measuring it between instrument faces, and neither automatically reproduces the installed joint. A measuring tool may contact only a small area. The assembly may load a broad face or a narrow pad through a very different restraint arrangement.

Keep the measurement method consistent and appropriate to the requirement. Identify the locations checked, the surface condition and any specified restraint. If the stack must be assessed in a fixture, define that fixture and how it is loaded. Otherwise, one inspector can report a satisfactory value while another reports a gap, with both unknowingly measuring different conditions.

Do not compensate for unstable seating by repeatedly changing thickness until one tightening happens to produce the target reading. First remove the source of the instability. The guide to shim burrs and contact faces explains how a small edge defect can dominate a seemingly straightforward stack.

Reassembly is where an undocumented stack becomes expensive

Once the machine is adjusted, the selected combination can disappear into a maintenance note such as “shim as required.” During later service, the layers are mixed, reversed or replaced from another assortment. The nominal total may be recreated while the original material, footprint or selected thickness range is lost.

Record the final approved combination in a way that matches the maintenance strategy. A fixed assembly can use identified spacer and shim part numbers. A selective assembly may need a record of the chosen grade or stack at each location. Keep the records linked to the equipment or assembly position, because identical-looking feet can require different corrections.

For custom metal shims and spacer plates, this leads to a more useful specification than a target total alone. Define acceptable layer combinations, individual thickness limits, common contact geometry and the final verification method. Then confirm the installed position using the equipment’s approved assembly procedure. The arithmetic remains necessary, but it becomes one part of a controlled joint rather than a substitute for checking how the parts actually meet.

Need a Custom Sheet Metal Quote?

Send us your CAD drawings — DRAmetal's initial response target is within 24 working hours. Quotation, DFM and lead-time timing depend on file completeness and engineering scope.

GET A FREE QUOTE →
DRAmetal Engineering Team

Team-authored manufacturing guidance. Scope, sources, corrections, and project-status labels follow our engineering content policy.