Two perforated sheets can have the same hole diameter and visibly different amounts of metal between the holes. They may suit the same nominal opening requirement, yet offer different clean open areas and behave differently when rolled, welded or loaded. Calling both “3 mm perforated stainless” loses much of the information needed to make a basket.
Keep three questions separate: what opening is required, how much of the patterned surface is open, and what metal remains to support the structure? These questions interact, but none is a substitute for the others. A useful drawing answers all three before a supplier selects stock sheet or proposes a custom pattern.
Hole size describes an opening, not a filtration guarantee
For round perforations, the nominal diameter identifies the individual hole. It does not describe the spacing, sheet thickness or finished condition of that opening. Those details belong alongside the diameter when the perforation is specified.
Nor does the nominal diameter establish an absolute particle-retention rating. Irregular particles can present different dimensions to an opening; deformable material can behave differently from rigid test particles. Gaps at a seam, rim or liner can also bypass the intended screening surface. The process owner needs to define what must be retained and how that requirement will be demonstrated.
If fine mesh is added, its aperture becomes a separate screening feature. Do not describe the perforated support hole as the fine filtration cutoff. Eaton’s published basket specifications distinguish perforations from mesh openings and show open area as another value. That is a useful specification pattern, not a transferable performance certification.
Open area is geometry before it is a flow calculation
For a repeating field of round holes, let D be hole diameter and P be center-to-center pitch, using consistent units. The McNICHOLS open-area reference gives:
- Straight centers: open area (%) = 78.54 × (D/P)².
- 60-degree staggered centers: open area (%) = 90.69 × (D/P)².
As a geometric example, 3 mm holes on 5 mm centers give approximately 28.3% for straight centers and 32.6% for 60-degree staggered centers. These are calculated pattern values, not measured basket flow rates. The change comes from arrangement even though hole diameter and nearest-center spacing remain the same.
Open area alone cannot predict pressure loss. Fluid properties, flow rate, wall thickness, entry conditions, additional screening layers and contamination also affect the application. A larger percentage is therefore an input to the hydraulic review, not proof that a basket will pass the required flow or remain within an allowable differential pressure.

The finished basket has less than a full field of holes
Catalogue open area commonly describes the repeating perforation pattern. The manufactured basket also includes unperforated seams, rim bands, bottom joints and possibly reinforcement. A housing support can obstruct another region. Multiplying the complete cylinder area by a pattern percentage without accounting for those areas can overstate the available opening.
Identify which surfaces are intended to pass fluid. A solid bottom should not be counted as screening area simply because it is part of the basket envelope. If the bottom is perforated, consider its own pattern and any covered joint region. The solid versus perforated bottom comparison addresses the consequences for drainage and service access.
For a geometric area estimate, split the assembly into identifiable exposed regions and apply the relevant pattern percentage to each. Record deductions and assumptions. A backed mesh assembly still needs a separate review of the two layers; adding their open areas together is not a meaningful description of the available flow path.
Ligaments are the metal the design still needs
For neighboring round holes, the edge-to-edge ligament along their centerline is pitch minus diameter. In the 3 mm/5 mm example, that distance is 2 mm. This arithmetic describes geometry, not an approved minimum ligament or a load rating.
Increasing the hole diameter at fixed pitch reduces the remaining metal. Reducing pitch at fixed diameter also narrows it. Either change therefore affects more than the opening percentage. The supplier must evaluate the proposed pattern with the material thickness, forming direction, seam layout and attachment details.
Keep handle pads, rim joints and other concentrated attachment regions visible on the drawing. An attachment landing partly over holes is not equivalent to the same detail on solid sheet. If solid margins are needed, specify them early; leaving them to fabrication can change both the useful open area and the finished layout. Structural review must also consider the permitted blocked condition, covered in the differential-pressure input guide.
Freeze the functional pattern, not just a catalogue shorthand
A release for custom perforated strainer baskets should state hole shape and size, pitch, arrangement, thickness, solid margins and the surfaces that are perforated. Identify any critical opening tolerance and the agreed inspection method rather than assuming a stock-sheet description covers the assembled part.
Allow a supplier to propose an alternative pattern only with the affected conditions visible. A change may preserve nominal hole size while altering ligaments, area, forming behavior and available weld land. That is an engineering substitution, not automatically an equivalent material purchase.
The best pattern is not necessarily the one with the smallest holes or greatest open area. It is the pattern that meets the defined separation requirement while leaving a manufacturable, supported and cleanable basket. Where a finer layer is required, reconsider the perforated-shell versus wire-mesh architecture instead of asking one sheet specification to solve every part of the duty.
Need a Custom Sheet Metal Quote?
Send us your CAD drawings — DRAmetal's initial response target is within 24 working hours. Quotation, DFM and lead-time timing depend on file completeness and engineering scope.
GET A FREE QUOTE →