AI & Industrial Equipment

Power Supply Enclosure: Inlet, PCB Supports and Fan Fit

A sheet-metal power-supply enclosure inside AI equipment, with C14 inlet, connector openings, fan perforations and PCB mounting supports.

Anonymous Customer Case Study

📅 October 15, 2026 ⏱ 5 min read 🏭 DRAmetal Engineering
Power Supply Enclosure: Inlet, PCB Supports and Fan Fit — component reference
Component reference image
0.5 mm Inlet fit clearance
7.95–8.05 mm Board-support height
10 pieces Dimensional first articles
3 pieces Complete fit trials

Project Overview

Application A sheet-metal power-supply enclosure inside AI equipment, with C14 inlet, connector openings, fan perforations and PCB mounting supports.
Materials 1.5 mm SPCC steel with M3 self-clinching standoffs and a powder-coated finish.
Fabrication route Cutting, bending, hardware insertion, pretreatment, powder coating, identification printing and mechanical assembly inspection.
Customer Challenge An oversized inlet opening allowed rocking, fan holes did not align and unequal supports allowed the PCB to contact the shell.
Design changes Actual-component inlet overlay and locating edge, revised fan pattern and countersunk features, and controlled standoff height checked with the real PCB.

An AI-equipment manufacturer needed to correct several mechanical fit problems in a power-supply enclosure. The original inlet cutout allowed movement, the fan attachment did not align as intended, and unequal board supports allowed the PCB to contact the metal shell.

The revised 1.5 mm SPCC enclosure used actual mating components to review those interfaces together. The project recorded a uniform 0.5 mm inlet fit clearance, board-support heights of 7.95–8.05 mm, and successful complete mechanical assembly on three first articles. These records describe mechanical fit, not qualification of the power supply’s electrical or thermal performance.

Three interface problems in one enclosure

The C14 inlet, fan and circuit board occupied the same compact enclosure, so their individual tolerances affected the final assembly. An inlet that could rock in its opening was not resolved simply by matching the overall enclosure size. Likewise, a flat-looking support arrangement could still place a board too close to the shell.

The customer supplied the relevant mating configuration. The power rating and internal bill of materials remain confidential. The published case focuses on the released metal interfaces and the quantities actually inspected.

Material and manufacturing route

The shell used 1.5 mm SPCC steel and M3 self-clinching standoffs. Fabrication included cutting, bending, hardware insertion, pretreatment, powder coating, silkscreen identification and mechanical assembly inspection.

The inlet was overlaid against the actual component. A revised locating edge and defined gap replaced the oversized opening. The fan pattern was corrected, with countersunk features where specified by the design. The board support arrangement used a consistent nominal height and was checked with the actual PCB.

Hardware insertion and coating belonged to the delivered configuration, rather than being treated as unrelated operations. The acceptance record therefore concerned the finished enclosure and its intended assembly, not only the bare cut-and-formed part.

C14 inlet fit on ten first articles

The project permitted an inlet fit gap of 0.3–0.8 mm. On September 10, 2026, ten first articles from a 500-piece batch were checked with the actual inlet and feeler gauges. The recorded gap was a uniform 0.5 mm, and the inlet did not rock in the reviewed fit.

The selected C14 component and its retention arrangement are part of that result. A different inlet sharing the same connector family name could need another panel opening or retention detail. The case does not define a universal C14 cutout.

PCB mounting and support-height checks

The mounting holes were nominally Ø3.2 mm, with recorded measurements of Ø3.18–3.22 mm. The standoffs were nominally 8 mm high, with results of 7.95–8.05 mm. Those checks covered ten first articles on September 10, 2026, using caliper measurements and the actual PCB.

The board sat flat and did not contact the shell in the trial. This is a mechanical assembly observation. It is not a substitute for the equipment designer’s electrical-spacing, insulation or safety assessment under the applicable operating conditions.

The recorded values preserve the distinction between nominal requirements and measured results. Neither the hole range nor the support-height range is presented as a general tolerance capability for every enclosure DRAmetal supplies.

Complete assembly on three units

The final mechanical trial was dated September 12, 2026. Three first articles from the 500-piece batch received the complete assembly check, and all three passed. The fan’s four attachment holes aligned in that configuration.

The complete trial quantity was three, not 500. The ten-piece dimensional checks and three-piece assembly trial addressed related but different acceptance tasks. Keeping their sample quantities separate avoids implying that every delivered enclosure received a fully populated assembly.

InterfaceRequirementRecorded resultCoverage
C14 inlet0.3–0.8 mm fit gapUniform 0.5 mm; no rockingTen first articles from 500; September 10
PCB holes / supportsØ3.2 mm holes; 8 mm support heightØ3.18–3.22 mm; 7.95–8.05 mm; board flat without shell contactTen first articles; September 10
Complete mechanical assemblySelected inlet, PCB and fan configurationThree of three passed; four fan holes alignedThree first articles from 500; September 12

Applying the project to another RFQ

The useful purchasing package includes the enclosure drawing, actual connector outlines, PCB mounting data, fan pattern and finished-state inspection plan. Reviewing those interfaces together reduces the ambiguity that an overall enclosure model alone can leave.

See custom power supply enclosures, the inlet-cutout guide and the variant fit-release guide when preparing a drawing-led OEM request.

More Manufacturing Projects

Explore More Manufacturing Work