Cabinet Panels and Covers
Outer panels, side covers, doors, top plates and access panels for BESS and energy infrastructure cabinets.
Energy Storage Sheet Metal Parts Energy Storage
Energy Storage
Sheet Metal Parts
Built for BESS and Power Equipment
Custom formed panels, brackets, trays, covers, airflow baffles and mechanical kits for BESS, battery modules, renewable energy enclosures and power infrastructure equipment. DRAmetal manufactures build-to-print parts with controlled interfaces, finish protection and project-level packout for OEM integration.
✓ Build-to-print scope
✓ Inspection by RFQ
✓ OEM approval boundary
RFQ Project-defined
RFQ
Example order size
Drawing
Critical dimensions
Plan
Inspection scope
OEM
Final approval
01 / What We Fabricate
Sheet Metal Parts for Energy Storage Equipment
Energy storage OEMs often need repeated sheet metal parts across cabinets, module racks, cable zones, airflow channels and service-access areas, supplied as controlled platform kits rather than as a single battery enclosure.
Module Support Parts
Battery module brackets, shelves, rails, trays and formed supports for repeated installation interfaces.
Thermal and Airflow Parts
Baffles, ducts, vent plates, louvers and airflow shields for thermal management zones.
Energy Equipment Kits
Revision-controlled sheet metal kits packed by cabinet, module bay, project stage or installation sequence.
Our scope: build-to-print energy storage sheet metal parts
The OEM owns battery cell selection, electrical architecture, BMS, fire safety, thermal validation and certification. DRAmetal manufactures the released sheet metal parts, hardware-ready kits and mechanical assemblies according to the approved drawings and inspection plan.
02 / Energy Storage Part Types
Panels, Brackets, Airflow Parts and Mechanical Kits
Use this component route for mixed trays, panels, brackets, covers and structural kits across an energy-storage assembly. For a complete outdoor cabinet or battery-pack housing, use the dedicated enclosure product page.
Cabinet Battery Cabinet Panels and Covers
Formed panels, doors, top covers, access covers and gland-area plates for energy storage cabinet programs.
- Materials Steel, aluminum, stainless
- Features Flanges, slots, inserts
- Use BESS cabinets
Module Battery Module Support Brackets
Shelves, rails, trays and formed supports used to locate battery modules, busbar zones and serviceable assemblies.
- Control Hole and datum checks
- Processes Cut, bend, weld
- Packout Bay or module kit
Thermal Airflow Baffles and Vent Parts
Louvers, vent grilles, baffles, ducts and deflectors that help control airflow paths inside energy storage cabinets.
- Features Perforation, louvers
- Risk Airflow obstruction
- Use Cooling zones
Kits Energy Storage Sheet Metal Kits
Finished panels, brackets and hardware-ready parts packed by cabinet revision, installation stage or project site.
- Control Drawing revision
- Quality Final inspection
- Delivery Project packout
03 / Technical Capabilities
Typical Energy Storage Sheet Metal Parts Specification
| Materials | Galvanized steel, cold-rolled steel, 304/316 stainless steel, 5052/6061 aluminum and project-defined coated materials |
|---|---|
| Processes | Laser cutting, punching, bending, spot welding, MIG/TIG welding, PEM hardware insertion, powder coating, passivation and assembly |
| Part examples | Cabinet panels, battery module rails, trays, covers, brackets, louvers, baffles, cable plates, gland plates and access panels |
| Quality controls | First article, CTQ hole inspection, flatness checks, coating review, hardware presence check and revision packout |
| Documentation | Drawing revision, BOM, finish specification, inspection record, material certificate and packaging photo when required |
| Delivery format | Loose parts, cabinet kits, module-bay kits, assembly-ready hardware-installed parts or export-protected project packs |
04 / Manufacturing Process
From Energy Storage RFQ to Project Packout
01
Application Review
Confirm BESS, battery module, renewable enclosure or power infrastructure application and the mechanical supply boundary.
02
Drawing and BOM Check
Review interfaces, thicknesses, coating notes, grounding areas, hardware, airflow features and revision control.
03
Fabrication
Laser cut, punch, bend, weld and deburr panels, brackets, trays and airflow parts to released drawings.
04
Surface and Hardware
Apply coating, passivation or plating, then install PEM hardware, studs, hinges or drawing-defined hardware where needed.
05
Interface Inspection
Check CTQ holes, mounting faces, gasket lands, module rails, finish quality and assembly-critical features.
06
Project Packout
Pack finished sheet metal parts by cabinet, module bay, installation sequence, drawing revision or project phase.
05 / Why It Matters
Why Energy Storage Parts Need Dedicated Manufacturing Control
Energy storage sheet metal parts sit between electrical, thermal, structural and service requirements. Small mechanical errors can affect module installation, cable routing, airflow, sealing and field maintenance.
Module Fit
Brackets, rails and trays must hold hole positions and datums so repeated battery modules install without rework.
Thermal Paths
Baffles, louvers and vent plates must match the system airflow strategy instead of becoming restrictions.
Outdoor Durability
Coating, galvanic compatibility and edge protection matter for long-life energy infrastructure cabinets.
Revision Control
Energy projects often change by cabinet generation, site requirement or module supplier, so packout must follow revision control.
Customer Project
Energy Storage Cabinet Kits: Common Mounting Interfaces
Materials, fabrication decisions and results for an anonymous customer project.
Component reference image
The Customer Challenge
Different finishes gave inconsistent corrosion protection, battery supports lacked capacity and mounting holes were not interchangeable.
Project Measurements & Details
≥200 kgSupport load test
≥50 typesParts per cabinet
20 ftContainer format
Results apply to the project configuration described on the linked page.
Explore Customer Projects → 07 / Why Choose Us
Why OEMs Use DRAmetal for Energy Storage Sheet Metal Parts
01
New energy fabrication experience
Battery trays, BESS enclosures, module racks and power cabinets give us practical experience with energy equipment interfaces.
02
Integrated fabrication flow
Cutting, bending, welding, finishing, hardware insertion and mechanical assembly can be coordinated under one supplier.
03
Interface-focused inspection
CTQ holes, module support faces, gasket lands, cable zones and hardware are checked against the drawing intent.
04
Project-level delivery
Parts can be packed by cabinet, module bay, site, revision or build sequence to reduce OEM sorting work.
08 / Related
Related Fabricated Products
09 / FAQ
Energy Storage Sheet Metal Parts FAQ
What energy storage sheet metal parts can DRAmetal fabricate?
We fabricate cabinet panels, doors, covers, brackets, battery module rails, trays, baffles, louvers, cable plates, gland plates and hardware-ready mechanical kits.
Do you build complete BESS systems?
We normally supply the mechanical sheet metal parts and assemblies. Battery cells, BMS, electrical integration, fire safety and system certification remain with the OEM or integrator.
Can you pack parts by cabinet or module bay?
Yes. Parts can be packed by drawing revision, cabinet, module bay, installation sequence or project phase.
Which details should be included in an RFQ?
Send drawings, STEP files, material and finish requirements, BOM, hardware list, CTQ dimensions, packout preference, annual volume and prototype quantity.
Get Started Need Energy Storage Sheet Metal Parts
Need Energy Storage Sheet Metal Parts
Ready for OEM Integration?
Send your drawings, BOM, material and coating notes, module interface requirements, hardware list, airflow features and expected quantities. We will review manufacturability, inspection and packout risks before quoting.